Turncraft manufactures a full selection of Coloinial design columns in a variety of wood species. Diameters ranging from 6" to 24" in two-inch increments. Heights range from 4' to 30' in two-foot increments. (Restrictions apply in diameter/height ratios. Turncraft Architectural offers a wider range of diameter -- 4" through 36".
On tapered Colonial columns, flutes start 9" from the top of the column shaft. For columns 6" through 20" diameter, the flutes end 7" from the top of the base. 22" and 24" columns, the flutes end 4" from the base. On non-tapered shafts, the flutes and 4" from the cap and 4" from the base.
Custom flute lengths are available on request, for the same price as standard fluted columns! If the column is using Ornamental Capitals, the fluting is adjusted to accomodate the capital height and correct trimming at the shaft neck ring or fillet.
Shaft lengths on wood columns are shorter than the overall height. The cap and base are attached to the ends of the shaft, providing the additional height.
|
 |
Nominal Shaft Diameter |
Shaft Dimensions |
Fluting Dimensions |
Outside Diameter |
Inside Diameter |
Number of Flutes |
Width of Flutes |
Bottom |
Top |
Bottom |
Top |
6" |
5 5/8" |
4 1/4" |
3" |
1 3/4" |
15 |
1/2" |
8" |
7 5/8" |
6 1/4" |
5" |
3 1/2" |
15 |
7/8" |
10" |
9 5/8" |
8 1/4" |
7 1/8" |
5 1/2" |
18 |
7/8" |
12" |
11 5/8" |
10 1/4" |
9" |
7 1/2" |
20 |
7/8" |
14" |
13 5/8" |
11" |
10 3/4" |
7 3/4" |
24 |
7/8" |
16" |
15 5/8" |
13" |
13" |
10" |
24 |
1" |
18" |
17 5/8" |
15" |
14 3/4" |
12" |
27 |
1" |
20" |
19 5/8" |
17" |
16 7/8" |
14" |
27 |
1" |
22" |
21 5/8" |
19" |
18 1/4" |
15 3/4" |
28 |
1 1/2" |
24" |
23 5/8" |
21" |
20 1/4" |
17 3/4" |
30 |
1 1/2" |
|
* For wood columns, inside sizes are based upon the inside diameter of the polyurethane cap. Other caps (wood and ornamental capitals) have different sizes and these numbers will not apply. |
Column Diameter |
Tapered |
Non-Tapered |
Inside Round |
Inside Square |
Inside Round |
Inside Square |
6" |
2 1/8" |
1 1/2" |
3 3/8" |
2 3/8" |
8" |
2 3/4" |
2" |
4 7/8" |
3 3/8" |
10" |
5 3/4" |
4" |
7 1/4" |
5 1/8" |
12" |
7 3/4" |
6" |
9 3/4" |
6 7/8" |
14" |
7 5/8" |
5 3/8" |
9" |
6 3/8" |
16" |
9 3/4" |
6 7/8" |
10 5/8" |
7 3/8" |
18" |
10 13/16" |
7 5/8" |
12 7/8" |
8 5/8" |
20" |
11 3/4" |
8 3/8" |
13 3/8" |
9 3/8" |
22" |
9 3/8" |
6 5/8" |
11 5/8" |
8 1/8" |
24" |
11 3/8" |
8" |
13 5/8" |
9 5/8" |
|
|
Stock # |
Shaft Bottom Diameter* |
Tapered & Non-Tapered Bases |
Tapered Caps |
Non-Tapered Caps |
Plinth |
Base Round |
Cap Round |
Abacus |
Cap Round |
Abacus |
A |
B |
C |
D |
E |
F |
G |
H |
I |
J |
K |
L |
Polyurethane |
2506 |
6" |
8 1/8" |
1 3/8" |
6 1/8" |
1 1/2" |
5 1/8" |
1 1/4" |
6 3/4" |
1 1/4" |
6 1/8" |
1 1/2" |
8 1/8" |
1 3/8" |
2508 |
8" |
10" |
1 3/8" |
8" |
1 1/2" |
6 3/4" |
1 1/4" |
8 3/4" |
1 1/4" |
8" |
1 1/2" |
10" |
1 3/8" |
2510 |
10" |
12" |
1 3/8" |
10" |
1 1/2" |
8 7/8" |
1 1/2" |
10 3/8" |
1 3/8" |
10" |
1 1/2" |
12" |
1 3/8" |
2512 |
12" |
14" |
1 3/8" |
12" |
1 1/2" |
10 3/8" |
1 1/2" |
12" |
1 3/8" |
12" |
1 1/2" |
14" |
1 3/8" |
2514 |
14" |
16 3/8" |
2 1/4" |
14" |
2 1/4" |
12" |
2 1/4" |
14" |
2 1/4" |
14" |
2 1/4" |
16 3/8" |
2 1/4" |
2516 |
16" |
18 3/4" |
2 3/8" |
16 3/8" |
2 5/16" |
13 3/4" |
2 3/8" |
16" |
2 3/8" |
16 3/8" |
2 5/16" |
18 3/4" |
2 3/8" |
2518 |
18" |
21 5/8" |
3 3/16" |
18 1/2" |
3 3/16" |
15 3/4" |
3 1/8" |
18 3/4" |
3 1/4" |
18 1/2" |
3 3/16" |
21 5/8" |
3 3/16" |
2520 |
20" |
23 3/4" |
3 3/8" |
20 1/2" |
3 1/8" |
17 5/8" |
3 1/4" |
20 5/8" |
3 1/4" |
20 1/2" |
3 1/8" |
23 3/4" |
3 3/8" |
2522 |
22" |
25" |
3 5/16" |
22" |
3 5/16" |
19 3/4" |
3 5/16" |
22 3/4" |
3 5/16" |
22" |
3 5/16" |
25" |
3 5/16" |
2524 |
24" |
28 1/2" |
3 5/16" |
24" |
3 5/16" |
21 3/4" |
3 5/16" |
25" |
3 5/16" |
24" |
3 5/16" |
28 1/2" |
3 5/16" |
Wood |
2006 |
6" |
8 -1/8" |
1 1/2" |
6 1/8" |
1 1/2" |
5 1/8" |
1 1/4" |
6 3/4" |
1 1/4" |
6 1/8" |
1 1/2" |
8 -1/8" |
1 1/2" |
2008 |
8" |
10" |
1 1/2" |
8" |
1 1/2" |
6 3/4" |
1 1/4" |
8 3/8" |
1 1/4" |
8" |
1 1/2" |
10" |
1 1/2" |
2010 |
10" |
12" |
1 1/2" |
10" |
1 1/2" |
8 7/8" |
1 1/2" |
10 3/8" |
1 1/2" |
10" |
1 1/2" |
12" |
1 1/2" |
2012 |
12" |
14" |
1 1/2" |
12" |
1 1/2" |
10 3/8" |
1 1/2" |
12" |
1 1/2" |
12" |
1 1/2" |
14" |
1 1/2" |
|
These tables reflect standard size, stock columns. Flute lengths will vary if columns are used with ornamental capitals. |
6" through 12" diameter Colonial Columns: |
Shaft Height |
Tapered |
Non-Tapered |
Flute Length (A) |
Straight Shaft (B) |
Flute Length (A) |
4' |
2' 2" |
0 |
2' 10" |
6' |
4' 2" |
0 |
4' 10" |
8' |
6' 2" |
0 |
6' 10" |
10' |
8' 2" |
2' |
8/ 10" |
12' |
10' 2" |
4' |
10' 10" |
14' |
12' 2" |
6' |
12' 10" |
16' |
14' 2" |
8' |
14' 10" |
14" through 24" diameter Colonial Columns: |
Shaft Height |
Tapered |
On 14" and larger non-tapered columns, the flute length will vary based upon the different cap/base heights for each diameter column. The flutes will end 4" from the base and 4" from the cap. To determine the flute length, you may subtract the cap/base from the overall height, and then subtract 8", giving you the exact flute length. Turncraft can flute any wood column for the exact height you require, at the standard fluted column price! |
Straight Shaft (B) |
6' |
0 |
8' |
0 |
10' |
0 |
12' |
0 |
14' |
2' |
16' |
4' |
18' |
6' |
20' |
8' |
22' |
10' |
24' |
12' |
26' |
14' |
28' |
16' |
30' |
18' |
|
|
|
About Us | Site Map | Privacy Policy | Contact Us | ©2007 Triton Architectural Columns